How to Install Stock ROM on Motorola XT1635-02 (Firmware Guide)

On this page, we have shared the download link and guide for installing the Motorola XT1635-02 (Moto Z Play, codenamed Addison) firmware flash file using the fastboot method. Here, you will find all the stock firmware zip files for all the supported regions with Motorola Z Play XT1635-02.

If you want to restore the device to factory firmware, this guide is for you. By using this guide, you can fix certain software-related issues such as hard brick, soft brick, WiFi, or Bluetooth issues, fix lag or stutter, or even downgrade the device anytime.

Steps to Install Motorola XT1635-02 Stock Firmware

Now, if you’re ready to flash the stock firmware manually on your Motorola Z Play XT1635-02 (addison) device then you need to download the flash tool, firmware file, and necessary drivers. So, without wasting any more time, let’s get into it.

Pre-Requirements:

• This ROM is supported for the Motorola Z Play XT1635-02 (addison) variant only.
• Ensure your device is charged at least 50% or higher.
• You will require a PC or Laptop with a USB Data Cable.
• We always recommend our readers take a full data backup of the device for safety purposes.
• Install Motorola USB Drivers and Rescue and Smart Assistant Tool on your PC
• To flash, you must download the ADB and Fastboot tool

Motorola Z Play XT1635-02 Firmware Flash Files:

Firmware Installation Guide:

Check out the firmware flashing guide below for the Motorola Z Play XT1635-02 (addison). First, install or extract the adb and fastboot tool on your PC. Now, enter the bootloader on your device.

Step 1. Bootloader Mode

Enter bootloader mode on your phone. To boot first, turn your phone off. Once your device turned off completely, press and hold the volume down, and turn it on. You should see the bootloader screen.

Step 2. Connect Your Device to PC:

After booting your Motorola Z Play into bootloader mode, now connect it to the PC using the USB Cable.

Step 3. Download Stock ROM/Firmware:

To get the full ROM, you can use the LMSA or Rescue and Smart Assistant Tool. Download the zip file and copy it to somewhere on your PC. LMSA tool will unzip the file and will remove the zip file you downloaded.

You can also download the full stock ROM from the above download flash file section on this guide.

Step 4. Flashing Guide:

1. The next step is to open the command window and go to the adb folder
2. Enter the following command to flash the firmware.

   *(fastboot flash bootloader bootloader.img) -> only when needed!
   fastboot flash modem NON-HLOS.bin
   fastboot flash fsg fsg.mbn
   fastboot erase modemst1
   fastboot erase modemst2
   fastboot flash bluetooth BTFM.bin
   fastboot flash dsp adspso.bin
   fastboot flash logo logo.bin
   fastboot flash boot boot.img
   fastboot flash system system.img_sparsechunk.0
   fastboot flash system system.img_sparsechunk.1
   fastboot flash system system.img_sparsechunk.2
   fastboot flash system system.img_sparsechunk.3
   fastboot flash system system.img_sparsechunk.4
   fastboot flash system system.img_sparsechunk.5
   fastboot flash system_b system_b.img_sparsechunk.0
   fastboot flash system_b system_b.img_sparsechunk.1
   fastboot flash system_b system_b.img_sparsechunk.2
   fastboot flash system_b system_b.img_sparsechunk.3
   fastboot flash oem oem.img
   fastboot erase cache
   fastboot erase carrier
   fastboot erase ddr
   fastboot reboot

3. Now your device will reboot into bootloader with the firmware you installed.

That’s it, guys. We hope this guide was helpful to you. Feel free to ask in the comment below for additional queries.